An ideal voltage source connected directly across an ideal short circuit produces a mathematical contradiction, not a physical event: the source must maintain a fixed nonzero voltage while the short forces that voltage to zero. No consistent current, voltage, or power exists. In real circuits, the outcome is set by whichever non-ideality dominates — source output impedance, wiring resistance, or protection circuitry.
The scenario is a limiting case that circuit theory uses to test models, and it exposes exactly where idealized element definitions break down. Understanding why requires separating what the schematic promises from what physics permits.
The Contradiction at the Heart of the Circuit
An ideal voltage source is defined by one rule: its terminal voltage equals its rated value regardless of current. An ideal short circuit is defined by the opposite rule: its terminal voltage is zero regardless of current. Place them in parallel and both rules apply to the same two nodes.
Kirchhoff's voltage law settles the conflict by making the system unsolvable. The loop equation reads V_source = V_short, which becomes 5 V = 0 V for a 5-volt source. No current value repairs that equation, because current does not appear in it.
This differs from the ideal current source feeding an open circuit, which is the dual paradox. There, a fixed current must flow through infinite resistance, and the required voltage diverges. Both cases share the same root cause: two ideal elements each insist on controlling the same variable.
A useful framing is that ideal models are promises about behavior, and the circuit asks two elements to keep contradictory promises. Circuit simulators handle this by refusing to solve — SPICE-style engines report a singular matrix, a floating node, or a voltage-source loop error rather than returning numbers. The error message is the software admitting the model has no answer.
In plain terms, the schematic describes a circuit that cannot exist, so the math declines to describe it.
Why Real Current Is Finite: Internal Resistance Sets the Limit
Every physical voltage source carries some internal resistance, and that single parameter converts the paradox into ordinary arithmetic. A real source behaves like an ideal voltage source in series with a small resistance, so shorting its terminals creates a simple divider: the current equals the source voltage divided by the total series resistance.
Grounded numbers make the scale concrete. A fresh AA alkaline cell sits near 1.5 V with an internal resistance around 0.1 to 0.3 ohm, so a dead short would demand roughly 5 to 15 A. A 12 V lead-acid car battery with an internal resistance near 0.005 ohm implies a theoretical short-circuit current around 2,400 A, which is why jumper cables and terminals are built to survive it. A lab bench supply rated 30 V at 3 A typically limits current electronically long before its 0.01-ohm output impedance would matter.
The current is finite because the source's own resistance dissipates the difference. Power delivered to an ideal short is zero by definition, since voltage across it is zero. All the energy lands inside the source and the wiring, which is the mechanism behind the heating described below.
This is the counterintuitive detail: the short circuit itself absorbs nothing. The damage happens everywhere except the component blamed for it.
Where the Energy Goes: Heat, Sag, and Self-Destruction
With voltage across the short at zero, the power balance shifts entirely to series resistances. Each resistive element in the loop dissipates current squared times resistance, so a 12 V battery pushing 600 A through 0.01 ohm of cable and contact resistance releases 3,600 W along that path.
That power density melts insulation, welds contact points, and can rupture a battery case. Automotive short-circuit incidents routinely destroy terminal clamps within seconds at currents in the hundreds of amperes. The cable becomes the fuse, and it does so unpredictably.
Source voltage also sags under load. A battery rated 12.6 V open-circuit may deliver only 9 to 10 V at its terminals during a heavy short, because the internal resistance drops the rest. The ideal model predicts constant voltage; the real source delivers a voltage that depends on what it is feeding.
Batteries add chemistry to the story. A lithium-ion cell shorted externally can exceed its designed discharge rate, drive internal heating, and trigger thermal runaway, which is why battery packs include fusible links and current-interrupt devices. The electrical short becomes an electrochemical event.
Comparison: How Different Sources Respond to a Bolted Short
| Source type | Typical internal resistance | Behavior into a short | Dominant limiting factor |
|---|---|---|---|
| Ideal voltage source (model) | 0 ohm | Undefined; no solution exists | Model contradiction |
| AA alkaline cell | 0.1–0.3 ohm | 5–15 A, rapid heating, voltage sag | Internal resistance |
| 12 V lead-acid battery | ~0.005 ohm | Hundreds to ~2,400 A, violent heating | Internal resistance and wiring |
| Lab bench supply | ~0.01 ohm plus control loop | Clamped at current limit, often 1–5 A | Electronic current limiting |
| Linear regulator output | Fraction of an ohm plus pass device | Thermal shutdown or foldback | Pass-element dissipation |
| Wall adapter (USB-class) | 0.1–0.5 ohm plus protection IC | Shutdown or hiccup mode | Protection circuitry |
The table shows a consistent pattern: as sources become more real, protection migrates from passive resistance to active electronics. The ideal case has neither.
The Time Course: Milliseconds to Minutes
| Time after short | What happens | Typical magnitude |
|---|---|---|
| 0–1 ms | Current rises toward the resistive limit | dI/dt set by loop inductance |
| 1–10 ms | Contact point heats; voltage sags | Hundreds of watts in contacts |
| 10–100 ms | Electronic protection trips on bench supplies | 1–5 A clamp typical |
| 0.1–2 s | Cable insulation softens; battery heats | Temperature climbs past 100 C locally |
| 2–30 s | Terminal damage, venting, possible fire | Energy release in kilojoules |
| 30 s–minutes | Thermal runaway risk in lithium packs | Cell temperature past 150 C |
Loop inductance matters in the first millisecond. Even a perfect 0-ohm source cannot change current instantaneously through real wiring, so the initial rise is rate-limited by geometry. This is why fast fuses and semiconductor protection can act before peak current arrives.
Edge Cases That Break the Simple Picture
Superconducting circuits approach the ideal case from below. A persistent-current loop in a superconducting magnet has essentially zero resistance, and a quench — a sudden loss of superconductivity — dumps stored energy into the former short path. Magnets store megajoules, and quench protection resistors exist precisely because the ideal short cannot persist safely.
Ideal sources in series with ideal shorts appear in textbook problems as limiting cases. Two ideal voltage sources of different values shorted together also produce no solution, for the same reason. Students who treat these as puzzles with hidden answers miss the lesson: the model, not the physics, has failed.
Very low-voltage sources matter too. A 1.5 V source shorted through 0.001 ohm still implies 1,500 A, but real contact resistance at the short itself — often 0.01 to 0.1 ohm — dominates. The short is rarely as ideal as the schematic symbol suggests, and contact resistance is frequently the largest term in the loop.
Misconceptions Worth Retiring
The most common error is expecting infinite current. Infinite current requires zero total loop resistance, and no physical loop achieves it; even welded busbars carry micro-ohms.
A second error is assuming the source survives because the short absorbs the energy. As shown above, the short absorbs nothing, and the source and wiring take the entire load.
A third error is confusing the ideal short with a low-resistance load. A 0.1-ohm resistor is a heavy load, not a short, and it draws a calculable current with normal circuit behavior.
Red flag: expecting a simulator to return a current value for an ideal source across an ideal short; it should refuse. Red flag: treating a bolted short as harmless because the short itself dissipates zero power. Red flag: assuming a power supply's current rating protects it without checking whether current limiting is enabled. Red flag: shorting lithium-ion packs for testing without fusing and remote switching. Red flag: relying on wire gauge alone when contact resistance may exceed conductor resistance.
Practical Actions and Thresholds
Engineers meet this scenario mostly by accident, so the practical guidance is about preventing and limiting it.
Verify source models before simulating. Replace ideal voltage sources with a series resistance of at least the datasheet's output impedance, and confirm the solver reports no voltage-source loops. A source with zero series resistance and a zero-ohm branch is a modeling error, not a result.
Enable current limiting on every bench supply and set it below the device's damage threshold, commonly 100 mA to 1 A for small electronics and up to the rated load for motors. Most supplies trip within milliseconds, fast enough to prevent most damage.
Fuse battery circuits at the pack terminal. A fuse rated 1.5 to 2 times the maximum expected load current clears a bolted short before cable insulation reaches its 105 C rating in typical automotive and hobby wiring.
Treat any measured loop resistance below 0.1 ohm as a short-circuit condition requiring active protection, because at 12 V that resistance implies currents above 120 A.
For high-energy systems, use remote switching and current-interrupt devices rather than manual disconnection. The arc from breaking a live short can exceed the hazard of the short itself.
What the Ideal Model Cannot Tell You
The ideal voltage source across an ideal short is best understood as a boundary marker. It tells you where circuit theory stops and where real-component parameters take over, and it reminds you that every element definition carries assumptions.
The model cannot predict current, heating, or failure because it contains none of the parameters that govern them. What it can do is flag a design or simulation that has drifted too far from physical reality.
The practical lesson survives the paradox: real short circuits are limited by resistance and interrupted by protection, and the component that fails is rarely the one drawn as the short.
This article is general educational information about circuit theory and electrical safety, not a diagnosis, treatment plan, or professional engineering opinion for any specific system. Do not test short circuits on high-energy sources without qualified supervision and appropriate protection. For work on batteries, mains wiring, or industrial equipment, consult a licensed electrician or electrical engineer.